TUNG PEI INDUSTRIAL CO., LTD.
886-2-27417321
886-2-27416623
10F., No.142, Sec. 4, Zhongxiao E. Rd., Da’an Dist., Taipei City 106, Taiwan
www.tpi.tw

Products

Deep Groove Ball Bearing
Deep Groove Ball Bearing

Design
Deep groove ball bearings are widely used in many industries for decades. A deep groove is formed on each inner and outer ring of the bearings enabling them to sustain radial and axial loads or even combinations of both. As the leading deep groove ball bearing factory, TPI Bearings owns abundant experience in designing and producing this type of bearing.

Inner and outer rings
Standard bearing steel with a content of carbon and chromium was selected and hardened to withstand the intense pressure between the rolling elements and bearing rings.
Carbonitriding on both inner and outer rings is a basic hardening process for TPI deep groove ball bearing factory. Through this special heat treatment, hardness on the raceway surface is increased; which reduces wear accordingly.
Ultra-clean steel is available in some product series from TPI ball bearings suppliers now, higher wear-resistance is obtained accordingly. Since contact fatigue is often caused by hard non-metallic inclusions, deep groove ball bearings nowadays require exceptional levels of cleanliness.

Rolling element
Steel balls with up to G3 grade ensure TPI deep groove ball bearing factory has the best stability and this also reflects in bearing performance under high speed rotation.
Ceramic balls is an additional option, when it comes to severe operating conditions. Extreme high speed rotation, heavy-duty applications and high heat generation while operating are some stiuations that ceramic balls can definitely help.

Cage
General cage designs for deep groove ball bearings and characteristic separately as below,

Pressed steel riveted cage, the most common design for a deep groove ball bearing. Widely used in bearings operating at dmN number under 350,000.
Pressed steel ribbon cage, normally used in bearings with smaller sizes, such as 608 or even smaller bearings.
Plastic snap cage, with lighter weight and lower heat generation, this nylon cage is perfect for bearings operating at dmN number above 350,000 and beneath 650,000, which is pretty much sufficient for deep groove ball bearings.

Seal
Two types of seals, contact and non-contact, were well designed by TPI precision roller bearings to effectively reduce the external dust entering the bearing while rotating.

Contact seal, prevent dust and liquid contamination from getting into the bearings. However, the torque will be higher and the limiting speeds will be lower under such application.
Non-contact seal, provide a general protection for the bearings. It cannot prevent liquid contamination from getting into the bearings. Torque and limiting speeds are same as the open type.

Grease
TPI deep groove ball bearing factory cooperates with the best grease manufacturers in the world which allows us to suggest and apply the best lubricating selection for our customers.

Life
Bearing life is usually expressed as the number of hours an individual bearing will operate before material fatigue develops on either the raceways or the rolling element. The usual life rating for industrial applications is called “L10” life. The L10 life is the number of hours which that 90% of bearings will survive; or, conversely, 10% of bearings will have failed in the L10 number of service hours.

Specification

Designation

The designation indicates the form, size, precision, internal structure, etc. of the bearing, and it's shown as below:

proimages/pro/Deep_groove_ball_bearing/DGBB-designations.png

Code Explanation
Special application
code
F- Stainless steel bearings
TS2- Dimension stabilized bearings for high temperature use (to 160℃)
TS3- Dimension stabilized bearings for high temperature use (to 200℃)
TS4- Dimension stabilized bearings for high temperature use (to 250℃)
CSB- Special heat treated long-life bearings
ESB- Special heat treated and material extra long-life bearings
EC- Expansion compensating bearings
AC- Creep preventing bearings
Cage L1 Machined brass cage
F1 Machined steel cage
G1 Machined brass cage, rivetless
G2 Pin-type steel cage
J Pressed steel cage
T1 Phenolic cage
T2 Plastic cage, nylon or teflon
Seal or shield LLB Synthetic rubber seal (non-contact type)
LLU Synthetic rubber seal (contact type)
LLH Synthetic rubber seal (low torque type)
ZZ Shield
LLE Better water resistance synthetic rubber seal
Ring configuration N Snap ring groove on outer ring (without snap ring)
NR Snap ring on outer ring
D Bearings with oil holes
Internal clearance C2 Radial internal clearance less than Normal
(CN) Normal radial internal clearance, but not shown in nominal numbers
C3 Radial internal clearance greater than Normal
C4 Radial internal clearance greater than C3
CM Radial internal clearance for electric motor bearings
NA Non-interchangeable clearance (shown after clearance code)
Tolerance standard (P0) JIS standard Class 0 (ABEC-1)
P6 JIS standard Class 6 (ABEC-3)
P5 JIS standard Class 5 (ABEC-5)
P4 JIS standard Class 4 (ABEC-7)
P2 JIS standard Class 2 (ABEC-9)
Lubrication 2AS TPI grease code
L627
3ES
5K

Mold
Machine
Vehicle
Contact Supplier
Browsing History
Scroll Up
EZB2B.TW uses cookies,IP to collect data and continually improve the website. By continuing to use this website, you must agree to the use of cookies and IP.